Tag: nissan

Not too long  ago I was looking for a second car to be my fun daily driver since driving the MS3 around was getting a little annoying to take to certain places, and it was limiting the amount customization I could be doing to the car itself. So, my search took me to Craig’s List, where I was looking for anything within my budget of below $2000.00 USD. In the end, I got the most unlikely car I was looking for, a 1991 Infiniti M30 coupe for less than $900.00.

The reason this car stood out to me was the body lines (basically the way it looked), the v6 motor, rear wheel drive, somewhat decent reliability, and the fact that it was compatible with many other Nissan parts from other models. Oh yeah and for the price (way below the budget) of the potential this car has was pretty worth it as well.

This is kind of a rare car being that it was one of the first Infiniti cars in North America, and about only about 6,000 coupes and 6,000 convertibles were made through the production years; 1990-1992. It is basically just a rebadged Nissan Leopard in Japan though, and shares similarities with the Nissan Z-chassis, R-chassis, Y-chasiss, and S-chassis. Because of that, I entered a world of mixing and matching parts.

Finding information was a definite mission with the downfall of forums, and the rise of social media, especially Facebook groups are to blame for that. First up was a 5 lug conversion and S13 coilover conversion. This pretty much meant upgrading most of the front suspension, which is straight forward plug and play, while the rear suspension had more modifications.

Front Suspension:
-S13 Powered By Max Competition front coilovers 5″ 30k
-S14 modified knuckles
-S14 stock 5 lug hubs
-S14 Duralast 5 lug brake rotors
-M30 stock brake calipers
-M30 Duralast brake pads
-S14 stock lower control arms
-GKTECH S14/S15 40mm roll center correction kit
-S14 MOOG outer tie rod ends
-Maxima MOOG inner tie rods
-S14 ISIS Pro tension rods

Rear Suspension:
-S13 Powered By Max Competition rear coilovers 5″ 22k
-Z31 5 lug rear stub axles
-Z32 Duralast 5 lug brake rotors
-Z32 stock brake calipers
-Z32 Duralast brake pads

Some of the main front suspension components.

The beautiful Powered By Max Competition coilovers. These are meant for S13, but with the right pieces and tweaks they should mount to the M30.

The front will mount with all the arms and knuckles. The rear will only be able to mount with modifying the M30 rear towers to match the S13 mounting points for the S13 top hats.

The stiffness.

The front coilovers maxed out with all the collars still placed at the top. Really short.

Added some paint onto certain items for protection and style.

Common on Nissan/Infiniti models for there to be wiring harness above the wheel well. This wiring harness above the driver side wheel well was labeled, cut, tucked, soldered, sleeved, and reloomed away inside and around the driver side front shock towers.

There was about 200 wires that needed attention after being cut and tucked inside the engine bay.

The biggest cock block for wanting to be low and somewhat functional.

Tucked inside the engine bay.

Also rerouted the hood latch cable inside the engine bay as well. Results are a worry free area to go low and run meatier tires.

The front was straight to the point, but required additional modifications to fix the roll center and tracking.

Because I was converting from 4 lug to 5 lug, this also meant that I needed wheels. After some research I found the appropriate wheel sizing I wanted to give the car. I went from the stock 4×114.3 wheels of 15×6.5 +20 to 5×114.3 15×10 +/-0. And of course did all that fender magic.

These are Vision 521 Nitro 15×10 +/- 0 with 205/50/15 tires all around.

The rear required new mounting points for the S13 top hats, Z31 rear 5 lug stub hubs, custom Z31 to M30 axle flanges, Z32 Duralast rear brake rotors, Z32 stock brake calipers, and Z32 Duralast brake pads.

Eventually, the whole rear end will be taken out to be replaced by S14 rear subframe and arms, but that isn’t until a later time.

Thanks. @shaviw